The following information must be submitted when applying for a permit for a commercial alteration/tenant improvement. Since every project is unique, there may be some situations where you will be asked to provide additional information.
ARCHITECTURAL PLANS(Minimum scale of plans to be 1/8”=1’. Single line drawings are not acceptable except as noted– plans must be drawn to show wall thickness)
- Foundation plans including all dimensions, construction details and references
- Building elevations reflecting exterior appearance of the building, exterior finish materials and height of the building above grade
- Floor plans indicating the use of all areas, complete dimensions and construction details and references
- Building sections with sufficient details to indicate necessary construction information
SITE PLAN(Scale site plans to most appropriate scale, e.g. 1”=10’ or 1/4”=1’) Minimum acceptable scale is 1” = 10’
- Property lines with dimensions, adjacent street names, easements, vicinity map, north arrow and lot area
- Property address and R number, legal description
- All site related improvements including grading, erosion control and stormwater drainage
- Existing and/or proposed grade elevations at property corners and corners of structure(s)
- Where a structure has a door, person gate or garage entry within five feet of a public street right-of-way, also include:
- Proposed finish floor elevations of doors, person gates and garage entries
- Elevations at top of the existing curb and back of the existing sidewalk and property line (perpendicular along the right-of-way)
- All new and existing structures on the site with distances from property lines and other structures. Include area (in square feet) of any existing buildings. Show basements that extend under public right-of-way.
- Utilities that include gas lines, power poles, street lights and all new and existing water meters and water piping (fire, domestic and irrigation) with points of connection to the City water system and related sizes
- All new and existing backflow valve installation locations
- All new and existing public and private sanitary and storm sewers and easements with points of connection and discharge
- Locations of all new and proposed fire hydrants (if none on-site, provide distance to nearest)
- Parking layout plan with dimensioned accessible parking spaces /aisles
- Driveways, width of adjacent right-of-way, public sidewalk, planting strip and/or tree wells, curb or edge of pavement
- Location, dimensions and area (in square feet) of all existing and proposed paving
- Landscaping, proposed and existing, to include both on-site information and street trees
- All easements and all supporting documentation and/or calculations
HVAC plans should indicate the locations for shafts, corridors, occupancy separations or other fire rated construction, the routing of duct work, locations for fire and smoke dampers at the penetrations through the fire rated construction and design criteria for outside air. Indicate locations for mechanical equipment and note the weights of equipment so that structural support can be verified. A separate mechanical permit is required and must be applied for prior to issuance of the building permit.
Indicate locations for lights, fans, smoke detectors, exit signs and egress lighting. Show compliance with building code electrical requirements. The electrical contractor must obtain a separate electrical permit.
Show the location, size and type of all new water, sanitary and storm water lines. Riser diagrams and fixture unit counts, existing and proposed, calculated in accordance with the Oregon State Plumbing Specialty Code, Table 6-4 must be provided for all projects with five or more fixtures. Identify how water, drain waste and vent pipes penetrating rated wall or floor/ceiling assemblies will be protected by listed assemblies. The plumbing contractor must obtain a separate plumbing permit.
STRUCTURAL PLANS(drawn to scale)
- Structural Calculations - One (1) sets of structural calculations prepared by the architect or engineer of record for the work covered. Calculations shall be sufficiently complete to demonstrate that the structural system is capable of supporting all imposed vertical and lateral loads and to demonstrate how loads are carried to the foundation. Calculations should include a design summary.
Foundation Plans and details, including piles, if any
Floor and roof framing plans showing all member sizes, connection details
Concrete design including sufficient details for the lateral load resisting system
Structural steel design details
General notes including design loads, grades of materials and material specifications, list of special inspection items, and list of deferred submittal items.
CIVIL PLANS(For simple projects, this information can be incorporated into the site plan where details are clearly shown)
- Erosion prevention and sediment control plan
- Paving plan
- Grading plan
- Excavation/shoring plan
- Stormwater drainage plan
To submit for a permit, bring the completed building permit application, commercial system development charge form, four (4) copies of required plans (for the area of proposed work and areas affected by such work), additional materials and intake fees to the Development Services Center.
- Specifications - two (2) sets of complete construction specifications. This information may be included on the plans for smaller, less complex projects where separate specifications are not part of the construction documents
- Life safety/building code summary
- Soils report - two (2) sets of soils reports prepared by a licensed engineer that details all needed site related soils information
- Energy code compliance documentation - must include the state-approved forms and worksheets for the summary, building envelope, lighting and HVAC
If you are hiring sub-contractors to do work on your project, and know who they are when applying, they will be listed on your permit at that time. If you don't know when you apply for your permit, they can be added after issuance. Sub-contractors you hire must be registered with the State of Oregon and carry a current CCB license.
THINGS TO CONSIDER:
- Code Summary
Applications for new buildings must show how they comply with the building code. A code summary is critical to convey design assumptions made for the building. Visit Plan Review staff at the Development Services Center or call (503) 823-7310 for code summary information.
- Change of Occupancy
Depending on the complexity of the project, a life-safety summary may be needed. This is similar to a code summary, but has more detail about sprinkler, fire alarms, detection systems and other construction information about the building. Visit Plan Review staff at the Development Services Center or call (503) 823-7310 for life-safety summary information.